If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Any Electricians out there. I need to extend 3 lighting cables (1.5mm). Can I extend these using terminal connectors? Would this meet regs, if not what do I use. Thanks for any advice.
Mick
ideally dont extend,try and re run it,if u have to extend go into electrical factors like city electrical etc,and get a junction box,its basically a 3/4/5 way connector block inside a round dome type job,just explain to them it's for 1.5mm cable and how many connections u need,when u get it,u will notice it doesnt look like u can get cables in,if u look in the sides once u unscrew the top there are cut outs,just use pliers to pull out the parts u need to to get cables in,
You main issue is, I think, that these days you need building regs approval to do pretty much anything. Check with your Council, and I'm sure a sparky'll pop up sometime to tell you the answer.
You main issue is, I think, that these days you need building regs approval to do pretty much anything. Check with your Council, and I'm sure a sparky'll pop up sometime to tell you the answer.
You're not "officially" allowed to do any domestic electrical work unless you are a qualified electrician with the necessary approvals. Anybody so approved would probably use a 5 amp junction box (round thingy with terminals inside) to extend a lighting circuit cable
You're not "officially" allowed to do any domestic electrical work unless you are a qualified electrician with the necessary approvals. Anybody so approved would probably use a 5 amp junction box (round thingy with terminals inside) to extend a lighting circuit cable
I believe you can do it if, it is passed afterwards by a qualified electrician
who can issue some certificate thing.
However I am not officially doing it
You do not need to inform the local authority for the following
1. Work consisting of -
(a) replacing any socket-outlet, control switch or ceiling rose;
(b) replacing a damaged cable for a single circuit only;
(c) re-fixing or replacing enclosures of existing installation components, where the circuit protective measures are unaffected;
(d) providing mechanical protection to an existing fixed installation, where the circuit protective measures and current carrying capacity of conductors are unaffected by the increased thermal insulation.
or for,
2. Work which -
(a) is not in a kitchen, or a special location,
(b) does not involve work on a special installation, and
(c) consists of -
(i) adding light fittings and switches to an existing circuit;
(ii) adding socket outlets and fused spurs to an existing ring or radial circuit; or
(iii) installing or upgrading main or supplementary equipotential bonding.
Go get a junction box, 5, 10 or 15 amp, 4 pole, and extend the wires, make sure that the junction box is in a suitable location (not plastered in a wall) and check your connections are tight, also please note that old house wiring was Red, Black and Green/Yellow but now we use Brown, Blue and Green/Yellow.
Connections are as follows
Live Red -- Brown
Neutral Blue -- Black
Earth Green/Yellow -- Green/Yellow
You should have it tested and certificated by a electrician who will, or should then have it checked by a building inspector (but that won’t happen)
i'm in the second year of my apprenticeship, but i'm good at doing lights as i'm 6'5", so everyone makes me do them as it saves getting the ladders off the van!
i'm in the second year of my apprenticeship, but i'm good at doing lights as i'm 6'5", so everyone makes me do them as it saves getting the ladders off the van!
Martin
Ah, so thats why I used to get all the plasterboard ceiling jobs.
Yeah use a mini 20 amp junction box or a Chockbox. Remember earth sleeving, proper termination, no tension on the cable.
Oh, and then-
Then from the DB, measure the Ze and prospective fault current. Then get an earth fault loop impedance reading from the light. After this, take your R1+R2 reading at the light either by measurement or by subtracting the Zs at the light from the Ze at the DB (better by measurement). Then using an insulation resistance tester set at 500v, check that the reading between phase-neutral, phase-earth, neutral-earth is greater than 200. Write all this down in your minor works certificate, remembering to state whether your earthing arrangement is TT, TN-S, TNC-S or other. Then pay those sods at the NICEIC or NAPIT to send it to them via the internet so they can approve it.
I couldn't tell you jack sh!t about mechanics though.
Comment