Injector pipes

[waveydavey00]

I am in the middle of an engine rebuild and foolishly did not mark the injector pipes on the way out. Doh!

Anyone know exactly which injector pipe goes where on the fuel pump? Two needed a bit of easing into place and have bent a bit so it is not obvious to which union they go. I think they are 1,2,3,4 counting clockwise from the bottom right and counting from the front of the engine for the cylinders

If anyone could confirm/point me in the right direction I would be grateful.

[BUSHWHACKER]

See your previous post!

[waveydavey00]

Thanks Vince. They look slightly different to mine. Is this the 3litre KZN130 engine?

[BUSHWHACKER]

I got it from here
http://www.toyotasurf.asn.au/techsite/

[waveydavey00]

I have looked at that site and it seeems to refer the same diagram to both 2.4 and 3.0ltr! The pipes look like they are routed and bracketed different to mine. I think 1 and 2 go to the lower outlets on the pump as they have not been bent! But the other two need a bit of friendly persuasion and could go either way.

Help

[BUSHWHACKER]

Sorry mate, can't help any further as mines a 2.4.
Maybe someone reading this with a 3litre will go and check for you and report back.

[waveydavey00]

Someone must be able to answer this: which injector pipe goes where on the kzn130 engine? It's 3 and 4 pipes I am having trouble with.

Please could anyone have a look on theirs. My rebuild is rained off at the moment but once the sun comes out or at least the rain stops I want to get it sorted.

[andy]

Not very clear but look at page FU16 here. http://www.showmesome.info/hilux/info/manuals/1KZ-TE/

[waveydavey00]

[QUOTE=andy]Not very clear but look at page FU16 here. [url]

Thanks Andy,

I have the same manual from Morr, but it is not as clear in mine as yours. I have even printed it off!

I think on this photo it goes 1,2 bottom r the l and then top 3,4 r and L.

The touble is I can see a blur between 3 and 4 where they may cross over and that is causing my confusion.

What do you think?

[andy]

Tried printing but my printer is $$$$ed, every time I look it gets more confusing.

[waveydavey00]

Cheers Andy. I think I will have to go with what I think is right. I am sure about 1 and 2 pipes 'cos they fit fine and look the same as the photo, but it's the other two that worry me. It will be sucg a pain to have to strip it again plus I will be thinking that is the problem if she won't start straight away. I will just have to keep trying and see what happens.

Thanks again for your help

[stevo]

injector pipes

The injector pipe sequence on the 2.4 is 1342 as you look from the rear of the pump, no'1 being top right, and continuing round in an anti-clockwise motion.Can't remember if the 3.0 is the same but most diesels run this way, hope this helps.
Cheers, Steve.

[Tallyman]

Just had a look at my 3.0L KZN130 for you. Standing at the radiator looking towards the bulkhead, the sequence is:

No. 1 = bottom left

No. 2 = bottom right

No. 3 = top left

No. 4 = top right

Hope this helps.

[waveydavey00]

Just had a look at my 3.0L KZN130 for you. Standing at the radiator looking towards the bulkhead, the sequence is:

No. 1 = bottom left

No. 2 = bottom right

No. 3 = top left

No. 4 = top right

Hope this helps.

Tallyman You're a star.

Just to be certain I will be looking exactly the opposite in terms of left and right when looking at the diesel pump from the back won't I? ( ie at the actual outlets on the pump) So the sequence is the same as I posted earlier? If I am wrong tell me now 'cos I plan to carry on with the job tomorrow.