3"S/Steel exhaust

[Macca81]

speaking of wheels, where did ya get those? cause they look identical to mine only mine are black instead of red... have never actually seen any other vehicle with them, let alone a surf...

also, that square red thing that sticks out past ya rear bar, where ya would normaly have a towball... that looks like it sticks out heaps, does it get caught up much offroad??

[POPEYE]

Love your truck Ian, wouldn't have done it any different myself.
So bl00dy jealous of those wheels!

One thing I've noticed you need to change though, the rear light clusters.
I've just changed mine for integral reverse light units and hooking them up to the centre lights so that I have four reversing lights.

Well thanks Vince, appreciate that, yup i do need to change em, i've been thinking about the lexus type replacement but i seem to remember some were a bit dodgy, i'll have to have a search on that subject, i have hooked up the small spots on top to the rev lights so i've at least some rev lights working, wired em via a DTDP toggle so i can switch em off, switch em on or have em working on reverse,

[POPEYE]

You could fit a pnuematic lift to your garage roof, I'm sure I've got another five port valve somewhere.

Hehe! i already thought about raising the roof (perhaps i should get biohazard to come round and raise it for me) if it was'nt attached to next doors garage it would be possible

[BUSHWHACKER]

Cheer's Jess, aye it's altered a bit, running out of stuff to do, i would like to do the full lift etc but would'nt get it in the garage which is the limiting factor
(alaong with the missis)

Love your truck Ian, wouldn't have done it any different myself.
So bl00dy jealous of those wheels!

One thing I've noticed you need to change though, the rear light clusters.
I've just changed mine for integral reverse light units and hooking them up to the centre lights so that I have four reversing lights.

[Webbo]

You could fit a pnuematic lift to your garage roof, I'm sure I've got another five port valve somewhere.

[POPEYE]

Nice Job Ian, looks a lot different to when I first saw it a couple o' years ago


There's always a Payback .... Ya just never ever see it Comin !!!!

Cheer's Jess, aye it's altered a bit, running out of stuff to do, i would like to do the full lift etc but would'nt get it in the garage which is the limiting factor
(alaong with the missis)

[Diezel Weazel]

Nice Job Ian, looks a lot different to when I first saw it a couple o' years ago


There's always a Payback .... Ya just never ever see it Comin !!!!

[POPEYE]

That finishes it of off great Ian top job mate, good choice me thinks.
It will soon be all black and sooty inside.

Thats what i thought mate, the soot will hide my "dabbing" and the splatter, thanks again Dave

[Webbo]

That finishes it of off great Ian top job mate, good choice me thinks.
It will soon be all black and sooty inside.

[POPEYE]

Hi Dave, fitted the trumpet end ring on there, repalced the last section to next joint and realigned it so it dose'nt hit the side tube, now it hits the sill a bit of rubber sorted that out tho, looks a lot better mate

[POPEYE]

post some pics of your truck and ill give you some ideas.

there ya go

[RodLeach]

Cheer's Dave and you other guys (all four of ya) dont know whats next mate, apart from a nice beveled end pipe outlet, running out of ideas
suggestions welcome (apart from ones suggesting i go away in short sharp jerks)

You could paint the chassis of my truck!

[blackpoolsparks]

post some pics of your truck and ill give you some ideas.

[POPEYE]

Top job Ian once again, I think I'm gunna start mine soon. Stainless welding can be a pain without Tig, you done a right nice job mate.Whats the next project ? You never seem to stop !!!!!!

Cheer's Dave and you other guys (all four of ya) dont know whats next mate, apart from a nice beveled end pipe outlet, running out of ideas
suggestions welcome (apart from ones suggesting i go away in short sharp jerks)

[Webbo]

Top job Ian once again, I think I'm gunna start mine soon. Stainless welding can be a pain without Tig, you done a right nice job mate.Whats the next project ? You never seem to stop !!!!!!