yobit eobot.com

Announcement

Collapse
No announcement yet.

Egr removal

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Overland Tonka
    replied
    Sancho....ask Matt about his pic....he has the answer...

    So pleased I didn't post it....

    Leave a comment:


  • frankx
    replied
    Originally posted by frankx View Post
    HI SANCHO that looks like bango connection in the photo drain plug for side engine oil ?
    i had to remove starter motor for overhaul do to so much cranking trying to get mobile the so what are ye trying to tell in photo?

    Leave a comment:


  • frankx
    replied
    Egr

    Originally posted by Sancho View Post
    Hope this helps

    HI SANCHO that looks like bango connection in the photo drain plug for side engine oil ?

    Leave a comment:


  • frankx
    replied
    EGR REMOvAL

    Originally posted by che2318 View Post
    Did you blank it or remove it?
    hi how doing sorry for delay ben down garage working on it.cranking over for hours .i noticed 2 loose wires joinged together with ring type connector 12mil hole centre coloured light brown green stripe across every 30 mil near rear end engine? cumming out the loom must had somthing to do with EGR removal cause thats only thing i was working on that side engine tested it registering 6.8 volts surely cant be earth? to manifold? every thing else fine glow plugs fuses .done diagnostic check E1 TE1for troubles engine lights flashes every 5 seconds ? GOT ANY IDEARS where the wire goes acording to codes downloaded off other site no 5. code correction resistance pump? i download engine control 2L TE circute diag. that shows connected to vsv intake and vrt vrp? were are they located under the bonnet?. which exlapins am getting airflow restriction to engine and that wire being of somthing to do with not starting? got any idears other members must had this experiance with hidden wire? while reoving EGR but i dont see any threads on it ecept one other member on old thread but doesent give the answer?
    Last edited by frankx; 5 November 2011, 19:59.

    Leave a comment:


  • Sancho
    replied
    Hope this helps

    Leave a comment:


  • frankx
    replied
    egr removal

    Originally posted by Vagrant No2 View Post
    May be the feed to the glow plugs ?
    hi rick with EGR valve now removed i discover loose wire comes out the loom at rear engine were EGR VALVE WAS LOCATED cant figour out where the ####er goes brown green stripe across it ring connection type with 12 m hole bolt on to somthing? where egr was located.i tested it registering 6.9 volts when ignition on. done diagnostic check pins E1 Te1 engine light flashs every 5 seconds code 5?which is listed as correction resistance pump ? any idears ? the hooks up to were
    Last edited by frankx; 5 November 2011, 14:57.

    Leave a comment:


  • BUSHWHACKER
    replied
    Originally posted by Wolfracer View Post
    ˇlooɔ s,ʇɐɥʇ
    ˙sʞuɐɥʇ

    It's grammar by the way.

    Leave a comment:


  • Wolfracer
    replied
    Originally posted by BUSHWHACKER View Post
    ˇpǝsnɟuoɔ ɯ,ı
    ˇlooɔ s,ʇɐɥʇ

    Leave a comment:


  • meooo
    replied
    i tink is a jiggle pin fault

    Leave a comment:


  • TonyN
    replied

    Leave a comment:


  • BUSHWHACKER
    replied
    ˇpǝsnɟuoɔ ɯ,ı

    Leave a comment:


  • Wolfracer
    replied
    Originally posted by dazandcaz View Post

    Leave a comment:


  • dazandcaz
    replied

    Leave a comment:


  • Wolfracer
    replied
    Originally posted by bullet513 View Post
    Errrrrrrmmmmmm ......... I'm a bit confused, maybe try using Microsoft word to check grammar then copy and Paste to hear, as I and others, by the look of it, can't understand what your trying to say.
    Think that more or less covers the punctuation and grammer...
    Last edited by Wolfracer; 3 November 2011, 22:38.

    Leave a comment:


  • bullet513
    replied
    haha stupid Iphone is crap

    Leave a comment:

Working...
X